NKE firmware update

Discussion and support for the Nmea4Wifi multiplexer - a 4-input Nmea 0183 wifi multiplexer.
Post Reply
WOOW
Posts: 13
Joined: Fri Nov 13, 2020 6:56 pm

NKE firmware update

Post by WOOW » Thu Mar 17, 2022 11:44 am

Hello,

NKE firmware update is done via original Box USB Datalog WiFi https://nke-marine-electronics.com/proj ... talog-wifi

Any chance it would be possible to update NKE firmware via Nmea4Wifi?

Luis Sa
Site Admin
Posts: 845
Joined: Thu May 04, 2017 4:12 am

Re: NKE firmware update

Post by Luis Sa » Thu Mar 17, 2022 2:16 pm

Hello,

I don't know about NKE. If you formulate your question more precisely, I will do my best to answer.

Regards, Luis

WOOW
Posts: 13
Joined: Fri Nov 13, 2020 6:56 pm

Re: NKE firmware update

Post by WOOW » Sun Mar 20, 2022 6:04 pm

Hello Luis, for firmware update NKE use TopLink2 software. I can send TopLink2 and manual to you to check if Nmea4Wifi "sees" it.

Luis Sa
Site Admin
Posts: 845
Joined: Thu May 04, 2017 4:12 am

Re: NKE firmware update

Post by Luis Sa » Sun Mar 20, 2022 7:32 pm

Hello,

OK, will try tomorrow but I can't promise to help!

Regards, Luis

My email is in the front page of the website

WOOW
Posts: 13
Joined: Fri Nov 13, 2020 6:56 pm

Re: NKE firmware update

Post by WOOW » Tue Mar 22, 2022 7:18 pm

Luis, thanks. Here is setup file with EN/FR user's manual https://mega.nz/file/9J0knKwB#fYnre4_IF ... kCxhq_ngTk

WOOW
Posts: 13
Joined: Fri Nov 13, 2020 6:56 pm

Re: NKE firmware update

Post by WOOW » Mon Mar 28, 2022 11:45 am

Hello Luis, maybe you had time to test?

dagnall
Posts: 459
Joined: Wed Mar 04, 2020 6:36 pm

Re: NKE firmware update

Post by dagnall » Mon Apr 04, 2022 4:03 pm

Hi, Luis has asked if I can look at this problem for you.

I have looked at the NKE setup that you have sent, and as far as I can see, the Toplink2 software must be run on a PC that is physically USB connected to the NKE box.

Although the NMEA4WIFI does have a USB output, It does not act as a simple "USB extension socket" to the PC.

I also note that the NKE manual is very specific and specifies that if the download is interrupted, it can mean that the NKE device will need to be sent back to the factory. (!) It is therefore probably a very bad idea to try and send these NKE uploads over a wifi link, in case they get corrupted.

I am sorry that this may not be the answer you wanted.

Best regards
Dagnall

WOOW
Posts: 13
Joined: Fri Nov 13, 2020 6:56 pm

Re: NKE firmware update

Post by WOOW » Tue Apr 05, 2022 12:56 pm

Hi Dagnall, thanks very much for your reply.

Could you please explain this "USB output does not act as a simple "USB extension socket" to the PC".

From my understanding USB output should create virtual COM port on PC, then this COM port is used in navigation software. Or not?

According to TOPLINK2 manual as USB port driver they use D2XX https://ftdichip.com/drivers/d2xx-drivers/

Also just in case here is the manual for NKE multiplexer https://mega.nz/file/5JVwHQwb#-i6ZfZtA_ ... bfO4hkU8mU

Post Reply