no update button on webpage
no update button on webpage
Hello
It's been a while since I updated my NMEA4WIFI unit firmware and it's several issues out of date.
So I tried to update my unit today and connected my pc via 192.168.4.1 and could see the setup page, but when scrolling down there was no update or file selection buttons. What have I missed?
Thanks
Paul
It's been a while since I updated my NMEA4WIFI unit firmware and it's several issues out of date.
So I tried to update my unit today and connected my pc via 192.168.4.1 and could see the setup page, but when scrolling down there was no update or file selection buttons. What have I missed?
Thanks
Paul
Re: no update button on webpage
Having read some other posts re updating firmware, maybe my version predates uploading via WiFi and it'll have to be done with a cable connection.
I'll try next visit.
Paul
I'll try next visit.
Paul
Re: no update button on webpage
Hello,
I do not know the present version that you are using. I think if you type 192.168.4.1:82 you can do the update.
Regards, Luis
I do not know the present version that you are using. I think if you type 192.168.4.1:82 you can do the update.
Regards, Luis
Re: no update button on webpage
Thank you Luis, I'll give it a try when I'm next on my boat.
Regards
Paul
Regards
Paul
Re: no update button on webpage
Hi Luis
I'm now wishing I had left it well alone!
My f/w version was 3.4 so was not able to update OTA and connected using a usb cable and followed the instructions using the ESP download tool.
However, I get no progress bar and a green SYNC flag while the black screen displays CONNECT BAUD: 115200 followed by a series of ....._____..... etc When I press STOP I get a message '2-sync fail'
I have set the Baud rate to 921600 and all other boxes as per the instructions. The unit is no longer generating a wifi network.
I am concerned that I have bricked the Wemos module even though the red and blue leds on the module are flashing in a sequence, so it seems to be listening to the PC and I have a data usb cable, not just power.
I think my NMEA4wifi may be an early version as in Device manger the usb port shows up as Silicon labs CP210x USB to UART bridge rather than the 340. Is this part of my problem?
In case it's the Wemos module can you tell me what I should buy as a replacement as there are multiple devices out there. Or hopefully you can advise what I'm doing wrong.
Many thanks
Paul
I'm now wishing I had left it well alone!
My f/w version was 3.4 so was not able to update OTA and connected using a usb cable and followed the instructions using the ESP download tool.
However, I get no progress bar and a green SYNC flag while the black screen displays CONNECT BAUD: 115200 followed by a series of ....._____..... etc When I press STOP I get a message '2-sync fail'
I have set the Baud rate to 921600 and all other boxes as per the instructions. The unit is no longer generating a wifi network.
I am concerned that I have bricked the Wemos module even though the red and blue leds on the module are flashing in a sequence, so it seems to be listening to the PC and I have a data usb cable, not just power.
I think my NMEA4wifi may be an early version as in Device manger the usb port shows up as Silicon labs CP210x USB to UART bridge rather than the 340. Is this part of my problem?
In case it's the Wemos module can you tell me what I should buy as a replacement as there are multiple devices out there. Or hopefully you can advise what I'm doing wrong.
Many thanks
Paul
Re: no update button on webpage
Well, just powered it off and back on and it seems to be working again, but still with f/w 3.4. So no further forward, but I still seem to have a working unit.
Very odd!
Very odd!
Re: no update button on webpage
Hello,
I will load version 34 here and will try to come from 34 to 60. Will paste here what I find. Please wait.
Regras, Luis
I will load version 34 here and will try to come from 34 to 60. Will paste here what I find. Please wait.
Regras, Luis
Re: no update button on webpage
Luis
my latest attempt at OTA , using192.168.4.1:82 seems to have worked and I now have version 6.0 on board.
Not sure why I was struggling before but all good now.
Thanks
Paul
my latest attempt at OTA , using192.168.4.1:82 seems to have worked and I now have version 6.0 on board.
Not sure why I was struggling before but all good now.
Thanks
Paul