How to update Nmea2wifi firmware
Re: How to update Nmea2wifi firmware
Hi Luís,
I tried to update the NMEA2WIFI multiplexer to the latest version 6.2 y 6.3 but after the flash of the firmware, the multiplexer didn't start. I tried several times without success, so I had to revert to version 5.8 that has worked.
When I restart it, the blue light does not stop flashing and the Wi-Fi network does not appear, if I go back to version 5.8 everything works.
The USB Cable is correct and the port reconnects it perfectly
Thank you
I tried to update the NMEA2WIFI multiplexer to the latest version 6.2 y 6.3 but after the flash of the firmware, the multiplexer didn't start. I tried several times without success, so I had to revert to version 5.8 that has worked.
When I restart it, the blue light does not stop flashing and the Wi-Fi network does not appear, if I go back to version 5.8 everything works.
The USB Cable is correct and the port reconnects it perfectly
Thank you
Re: How to update Nmea2wifi firmware
Hello Juanvi,
Please check this forum again. I have revised this topic. Please try to flash the OTA_BLINK.bin file as described.
Regards, Luis
Please check this forum again. I have revised this topic. Please try to flash the OTA_BLINK.bin file as described.
Regards, Luis
Re: How to update Nmea2wifi firmware
Thank you very much Luis, I have managed to update it to version 6.3
Re: How to update Nmea2wifi firmware
Hello,
Thank you for the feedback. I don't understand why it didn't work in the normal way but at least we found a way to update shall it be necessary.
Regards, Luis
Thank you for the feedback. I don't understand why it didn't work in the normal way but at least we found a way to update shall it be necessary.
Regards, Luis
Re: How to update Nmea2wifi firmware
Hi, I have been using nmea2wifi with Digital Yacht AIT250 and it’s been great! I have never upgraded the firmware from the version 5.6.
Now I am ready to upgrade it but I am struggling to find an instruction how to do it… I would like to start with the major upgrade from 2019 to obtain possibility to use wifi for further upgrades. Please look at the screenshot attached- there is no button “Upgrade” on the browser webpage…. What device (Windows-iOS-Android) do I need to use? Any help would be greatly appreciated!
Waldemar
Now I am ready to upgrade it but I am struggling to find an instruction how to do it… I would like to start with the major upgrade from 2019 to obtain possibility to use wifi for further upgrades. Please look at the screenshot attached- there is no button “Upgrade” on the browser webpage…. What device (Windows-iOS-Android) do I need to use? Any help would be greatly appreciated!
Waldemar
Re: How to update Nmea2wifi firmware
Hello Waldemar,
You need to follow the steps in the beginning of this post. Once you get a newer version supporting OTA changing from one version to another is very easy. Unfortunately at the time of 5.6 the update was not so simple.
If you know how to use Arduino to flash an ESP8266 module, there is an alternative. Otherwise you need to follow the steps in this post.
Regards, Luis
You need to follow the steps in the beginning of this post. Once you get a newer version supporting OTA changing from one version to another is very easy. Unfortunately at the time of 5.6 the update was not so simple.
If you know how to use Arduino to flash an ESP8266 module, there is an alternative. Otherwise you need to follow the steps in this post.
Regards, Luis
Re: How to update Nmea2wifi firmware
Hi Luis,
I am back on the boat in Lanzarote and trying to update the firmware. I have followed your instructions (factory settings-disconnect device-connect to my Windows 11 laptop). The device manager can see a usb device but no driver installed. I downloaded, unzipped the driver file using link in your instruction but an error occurred… Please look at the screenshots attached. Could it be that the driver is not compatible with the ARM-based system….
Any ideas how to help it?
Thank you, best regards
Waldemar
I am back on the boat in Lanzarote and trying to update the firmware. I have followed your instructions (factory settings-disconnect device-connect to my Windows 11 laptop). The device manager can see a usb device but no driver installed. I downloaded, unzipped the driver file using link in your instruction but an error occurred… Please look at the screenshots attached. Could it be that the driver is not compatible with the ARM-based system….
Any ideas how to help it?
Thank you, best regards
Waldemar
Re: How to update Nmea2wifi firmware
Hello Waldemar,
That driver is not only necessary to update the firmware using a USB cable but it is also necessary if the multiplexer has to receive or send nmea0183 data from/to a PC, through USB. I don't know if it is possible to install the driver on Windows11 ARM. Just saw here that some people have difficulties:
https://www.reddit.com/r/lasercutting/c ... m_edition/
The official site from the manufacturer is this:
https://www.wch-ic.com/downloads/category/30.html
I wonder if you are able to use another PC just to flash it.
Sorry for not being able to help more, Luis
That driver is not only necessary to update the firmware using a USB cable but it is also necessary if the multiplexer has to receive or send nmea0183 data from/to a PC, through USB. I don't know if it is possible to install the driver on Windows11 ARM. Just saw here that some people have difficulties:
https://www.reddit.com/r/lasercutting/c ... m_edition/
The official site from the manufacturer is this:
https://www.wch-ic.com/downloads/category/30.html
I wonder if you are able to use another PC just to flash it.
Sorry for not being able to help more, Luis
Re: How to update Nmea2wifi firmware
Thank you very much Luis, I will do more research but most likely I will have to take the device home and try to do it on another PC…
Best wishes
Waldemar
Best wishes
Waldemar
Re: How to update Nmea2wifi firmware
Hi Luis
Just to let you know that after a few attempts and communication with the driver developer I have managed to flash the unit and update the firmware to the latest version!
Thank you very much for your help
Best regards from Lanzarote
Waldemar
PS. The link to the driver for ARM systems
https://www.wch-ic.com/downloads/CH341SER_EXE.html
Just to let you know that after a few attempts and communication with the driver developer I have managed to flash the unit and update the firmware to the latest version!
Thank you very much for your help
Best regards from Lanzarote
Waldemar
PS. The link to the driver for ARM systems
https://www.wch-ic.com/downloads/CH341SER_EXE.html